SELECT DISTINCT shop_view_active_item.*
FROM shop_item_has_category
INNER JOIN shop_view_active_item ON (
shop_view_active_item.company = shop_item_has_category.company AND
shop_view_active_item.shop_code = shop_item_has_category.shop_code AND
shop_view_active_item.language_code = shop_item_has_category.language_code AND
(
shop_item_has_category.item_no = shop_view_active_item.item_no
)
)
WHERE (shop_item_has_category.category_line_no = 95000)
AND shop_view_active_item.language_code = 'ENU'
AND shop_view_active_item.company = 'DESOI'
AND shop_view_active_item.shop_code = 'B2B'
AND shop_item_has_category.company = 'DESOI'
AND shop_item_has_category.shop_code = 'B2B'
AND shop_item_has_category.language_code = 'ENU'
AND shop_item_has_category.category_shop_code = 'B2B'
Artikel zum
Warenkorb hinzufügen
Alle gewählten Artikel
zum Warenkorb hinzufügen
Artikel aus Warenkorb
entfernen
Merkliste
Merkliste
Artikel nicht auf Lager
Vorbestellung möglich
Artikel in geringer
Menge auf Lager
Artikel in ausreichender
Menge auf Lager
Artikel in Zulauf
Der Artikel ist in einer laufenden
Aktion enthalten
Injection method for masonry with cavities
Due to a multistage injection in a low-pressure process, cavities, defects and fissures are filled with a shrinkage-free injection mortar via bore packers. Using the same packers, a drill channel is created by a lance. The injection material is then injected by pressure injection (3-5 bar) for better distribution. In this way an optimal effectiveness in the area of the injected masonry can be achieved.
Horizontal sealing / Horizontal barriers
Subsequent injection against capillary ascending moisture
open PDF
Objectives
- Prevention of moisture flow by capillary action
- Moisture content in equilibrium with environment
- Prevention of capillary moisture replenishment above the injection zone
Objectives of low-pressure injection
- In the case of masonry of homogenous materials
- In the case of masonry with a high rate of moisture transport
- Consistent and rapid distribution of injection material throughout the masonry
Advantages
- Machine pressure injection contributes to optimal distribution of filling material in masonry
- Packer systems and fittings optimized for the technique
- Strengthening and stabilization of masonry in the injection area
- Low consumption of injection fluid through filling of internal cavities
Types of packers
- Bore packers (steel)
- Drive-in packers (polymer)
Requirements with regard to Injection and Mixing Equipment
- Cross section adjusted to the flow characteristics of the injection material
- Pressure controlled and limited to between 1 and 15 bar
- Corrosion resistance of all equipment parts vis-a-vis injection material
- Homogenous mixing of injection material
- Consistent mixing quality
- Keeping the injection material in motion
- Pump performance and flow suitable to the masonry
Note
- The horizontal seal should only be injected above the pressure and water line
Additional information in German: „Injektionsverfahren mit zertifzierten Stoffen gegen kapillaren Feuchtetransport“ WTA Merkblatt E.4-10, Ausgabe 03.2015/D.
Wet-on-Wet Technique and Multistage Injection (INJECTION PASTE AND MICRO EMULSION)
Objectives of the Wet-on-Wet Technique
- Filling of the internal cavities to create an injection zone to contain the micro
emulsion
- Stabilization of the masonry in the area being injected
- Increase of alkalinity in the area injected to allow the micro emulsion to react
Filling materials
- Injection of paste (step 1)
- to fill cavities and crevices
- Injection of micro emulsion (step 2)
- to create a horizontal seal
Objectives of Multistage Injection
- In the case of masonry of homogenous materials and a low alkalinity, the chemical reaction is started using an activator
Procedure Wet-on-Wet Technique – Step 1
- Prepare drilling by marking the positions of holes every 10 to 12.5 cm (4 to 5 inches) then drill and remove dust with a moist cloth or brush
- Insert packers, clamp, and attach shut-off pieces
- Mix injection paste
- Fill the injection pump with mixed material
- Inject the drill holes at a pressure of approximately 2 bar (depending on masonry)
Procedure Wet-on-Wet Technique – Step 2
- When injection pressure has dropped sufficiently (when material stops flowing out of the shut-off piece) insert the test lance into the packer. The channel for the second injection is ready when the injection paste has hardened enough that the test lance can be withdrawn
- Mix micro emulsion and inject into drill holes at a pressure of approximately 5 bar (depending on masonry)
Wir brauchen Ihr Einverständnis!
Wir benutzen Drittanbieter, um Videoinhalte einzubinden. Diese können persönliche Daten über Ihre Aktivitäten sammeln. Bitte beachten Sie die Details und geben Sie Ihre Einwilligung.
Mehr Informationen
Externe Medien Akzeptieren
Wir brauchen Ihr Einverständnis!
Wir benutzen Drittanbieter, um Videoinhalte einzubinden. Diese können persönliche Daten über Ihre Aktivitäten sammeln. Bitte beachten Sie die Details und geben Sie Ihre Einwilligung.
Mehr Informationen
Externe Medien Akzeptieren
